1/8 DIN Temperature Controller Heat/Cool Controllers

FuzyPro 1 /8 DIN Temperature Controller Heat/Cool Controllers are designed to provide precise control with a quick and easy set up procedure. SMT and microprocessor technology provides all these features plus reliability and economy. LED index indication allows full viewing and selection of parameters.

The dual display allows set point and process value visibility at all times. An advanced software algorithm automatically calculates all PID parameters to eliminate complicated manual tuning efforts. Automatic tuning can be bypassed if manual tuning is preferred. An open-loop, manual mode can be initiated if the sensor fails. Front panel electronic calibration sensor linearization self-diagnostic capabilities and cold junction compensation are all performed by the single chip microprocessor. The in-panel depth is only 2-1/2".

FuzyPro 1 /8 DIN Temperature Controller Heat/Cool Controllers Features:

• Automatic tuning of PID parameters
• Selectable input
• Dual heating and/or cooling outputs with 2 alarms
• ºF or ºC display. Dual display. Sealed mylar front panel
• Security code protection, automatic manual mode operation
• All control parameters adjustable from front panel
• 3 year warranty. 2-1 /2" in panel depth

FuzyPro 1 /8 DIN Temperature Controller Heat/Cool Controllers Specifications:

INPUT

Thermocouple	Type J,K.T.B.E,R,S,N selectable
RTD	PT 100ohm (DIN or JIS)
Linear	-10-60mV Configurable input or voltage or current
Display	Temperature or engineering units
OUTPUTS	Single output with 2 optional independent alarms Heating and cooling outputs with 2 optional Alarms
Relay	SPST relay rated 3A, 240V maximum resistive load
Pulsed Voltage	32VDC,2OmA maximum ohms
Current	4-20mA,0-20mA maximum load 500 ohms
Voltage	0-10V minimum load 500K ohms
Alarms	8 selectable modes each alarm SPST relay(s) rated 2A, 240V maximum resistive load.

CONTROL FEATURES

Temp Range	Selectable Set Point: -1999-3182F/-1128-1750C
Alarm Set Point	Full Range Adjustable
Control Modes	Controls can be configured as On/Off Proportional (P) Proportional with manual reset                              Proportional/Integral (PI) Proportional                              Derivative (PD)                              Proportional/Integral/Derivative (PID)                              Heating and Cooling Proportional Band: 0-100% of span
Integral (Reset)	0-3600 seconds
Derivative(Rate)	0-1000 seconds
Anti-Reset Wind-up	Inhibits integral action outside of proportional band.
Cooling	Adjustable deadband from-10 to + 10% of cooling proportional band
Manual Mode	Configurable as open loop control should sensor no longer function
Cycle Time	0-120 seconds
Sensor Break Protection	Configurable status of control and alarms
Control Action	Selectable-Direct action for cooling Reverse action for heating

INDICATION

Display	4 digit red 5/8" LED Process Value Display. Green 1.2" LED Set Value display Selectable decimal placement for normal or high resolution display
Example	0000, 000.0, 00.00 or 0.000
F/C	Selectable with 2 LED indicators
Sample Rate	250 milliseconds
Power Supply	90-26OVAC, 50/60Hz Consumption: less than 5VA
Data Retention	l0 years (EEPROM)
Control Stability	+ -0.15% of full scale
Accuracy	+ -0.25% of range: + -1 c or 0.5C in high resolution
Cold Junction Compensation	0.1% ambient
External Resistance	100 ohms maximum
Common Mode Rejection	120dB
Normal Mode Rejection	60dB
Input Impedance	10M ohms
Operating Temperature	14-122ºF (-10-50ºC)
Humidity	0-90% RH(non-condensing)
Insulation	20M ohm minimum (5OOVDC)
Breakdown	2OOVAC, 50/60Hz 1 minute
Vibration	10-55Hz amplitude 1 mm
Shock	200m/c (20g)